ABS pipe
DATE：2022/9/21 9:06:18 / READ： / SOURCE：This station
ABS pipe
ABS is a kind of plastic pipe which is made of BS resin as raw material after being plasticized and melted by an extruder.
(1) D1 has been introduced
It is a copolymer of acrylonitrile, butadiene and styrene. The pipe formed with ABS resin has the synergistic effect and characteristics of the three monomers. ABS pipes are tough, hard, dimensionally stable, non-toxic, chemical-resistant, wear-resistant, heat-resistant, cold-resistant and electrical
The mother is good, good and other characteristics, and the surface is easy to chrome plating; but the ABS pipe is not resistant to ketones, aldehydes and chlorinated hydrocarbons. Due to its excellent performance, ABS pipes are widely used, and can be used in some fields to replace metal pipes; ABS pipes are used as air ducts and water supply and drainage pipes in the marine industry, and are used to transport chemical corrosives with a certain temperature and pressure. liquid, available in
(2) ABS pipe is used within the temperature range of 2~20 ℃, but it should not be used outside the meal.
But set the first Li Yin, all manufacturing, inspection → Jinjin library, ABS tree, wandering child, green virgin, anti-extraction machine, plasticizing raw materials to make them molten, mold agricultural management
(3) Under the conditions, the extrusion molding of ABS pipe mainly adopts the structure of single screw extruder screw. Generally, the same thread pitch should be used, and the thread depth should be gradual; Compression ratio in the range of ~18)1 is (3~4)1-type pipe general structure
(4) Forming process
There are many types of BS resins, and resins suitable for extrusion should be selected, such as E-7 produced by the synthetic rubber factory of Lanzhou Petrochemical Industry Company.
3 or E1 type ABS resin.
②Before the raw materials are put into production, they should be dried and dehumidified in an oven at 70~80℃46
Control the moisture content below 0.1%.
The plasticizing section is 165~180℃, and the homogenizing section is 170~180℃. .③The plasticized raw material is in molten state, and the temperature of the extruder barrel is 150~165℃ in the feeding section
④The temperature of the forming die for forming the tube blank is 175~190℃. ⑤ The draft ratio is 1~1.2.
⑥The temperature of circulating water for cooling and shaping is 15~22℃. (5) Key points of process operation
① The process temperature control for extruding ABS resin should be as low as possible. Pay attention that the residence time of the molten material in the barrel should not be too long to avoid the decomposition of the molten material. The decomposition temperature of the melt is 250°C. ② When producing ABS pipes, the color of the melt should be observed frequently, and the plasticizing temperature should be reasonably controlled if the melt is pale yellow. When the molten material is light green gray, it means that the temperature of the barrel is too high, and the temperature of the barrel should be lowered immediately.
③The distance between the sizing sleeve and the die should be controlled within the range of 15~35mm.
④If the temperature control of the barrel process is reasonable, but there is still a phenomenon of melt decomposition (the color of the melt is light blue-gray), it should be considered that the length-diameter ratio of the screw should be smaller.
⑤ The working speed of the screw should not be too high, generally not more than 20r/min.
(6) Quality requirements The quality requirements of ABS pipes should comply with HG21561-94 -346-
(2) ABS pipe is out of the molding production process route - use within the temperature range of 2 ~ 20 ℃, but pay attention to this kind of pipe should not be used outside the meal, but it should be determined first, all systems, inspection → inspection → ABS tree The wandering green virgin one anti-exit machine plasticizes the raw material to make it molten one mold agricultural management
(3) Under the conditions, the extrusion molding of ABS pipe mainly adopts the structure of single screw extruder screw. Generally, the same thread pitch should be used, and the thread depth should be gradual; Compression ratio in the range of ~18)1 is (3~4)1-type pipe general structure
(4) Forming process
There are many types of BS resins, and resins suitable for extrusion should be selected, such as E-7 produced by the synthetic rubber factory of Lanzhou Petrochemical Industry Company.
3 or E1 type ABS resin.
②Before the raw materials are put into production, they should be dried and dehumidified in an oven at 70~80℃46
Control the moisture content below 0.1%.
The plasticizing section is 165~180℃, and the homogenizing section is 170~180℃. .③The plasticized raw material is in molten state, and the temperature of the extruder barrel is 150~165℃ in the feeding section
④The temperature of the forming die for forming the tube blank is 175~190℃. ⑤ The draft ratio is 1~1.2.
⑥The temperature of circulating water for cooling and shaping is 15~22℃. (5) Key points of process operation
① The process temperature control for extruding ABS resin should be as low as possible. Pay attention that the residence time of the molten material in the barrel should not be too long to avoid the decomposition of the molten material. The decomposition temperature of the melt is 250°C. ② When producing ABS pipes, the color of the melt should be observed frequently, and the plasticizing temperature should be reasonably controlled if the melt is pale yellow. When the molten material is light green gray, it means that the temperature of the barrel is too high, and the temperature of the barrel should be lowered immediately.
③The distance between the sizing sleeve and the die should be controlled within the range of 15~35mm.
④If the temperature control of the barrel process is reasonable, but there is still a phenomenon of melt decomposition (the color of the melt is light blue-gray), it should be considered that the length-diameter ratio of the screw should be smaller.
⑤ The working speed of the screw should not be too high, generally not more than 20r/min.
(6) Quality requirements The quality requirements of ABS pipes should comply with HG21561-94 -346-
ABS is a kind of plastic pipe which is made of BS resin as raw material after being plasticized and melted by an extruder.
(1) D1 has been introduced
It is a copolymer of acrylonitrile, butadiene and styrene. The pipe formed with ABS resin has the synergistic effect and characteristics of the three monomers. ABS pipes are tough, hard, dimensionally stable, non-toxic, chemical-resistant, wear-resistant, heat-resistant, cold-resistant and electrical
The mother is good, good and other characteristics, and the surface is easy to chrome plating; but the ABS pipe is not resistant to ketones, aldehydes and chlorinated hydrocarbons. Due to its excellent performance, ABS pipes are widely used, and can be used in some fields to replace metal pipes; ABS pipes are used as air ducts and water supply and drainage pipes in the marine industry, and are used to transport chemical corrosives with a certain temperature and pressure. liquid, available in
(2) ABS pipe is used within the temperature range of 2~20 ℃, but it should not be used outside the meal.
But set the first Li Yin, all manufacturing, inspection → Jinjin library, ABS tree, wandering child, green virgin, anti-extraction machine, plasticizing raw materials to make them molten, mold agricultural management
(3) Under the conditions, the extrusion molding of ABS pipe mainly adopts the structure of single screw extruder screw. Generally, the same thread pitch should be used, and the thread depth should be gradual; Compression ratio in the range of ~18)1 is (3~4)1-type pipe general structure
(4) Forming process
There are many types of BS resins, and resins suitable for extrusion should be selected, such as E-7 produced by the synthetic rubber factory of Lanzhou Petrochemical Industry Company.
3 or E1 type ABS resin.
②Before the raw materials are put into production, they should be dried and dehumidified in an oven at 70~80℃46
Control the moisture content below 0.1%.
The plasticizing section is 165~180℃, and the homogenizing section is 170~180℃. .③The plasticized raw material is in molten state, and the temperature of the extruder barrel is 150~165℃ in the feeding section
④The temperature of the forming die for forming the tube blank is 175~190℃. ⑤ The draft ratio is 1~1.2.
⑥The temperature of circulating water for cooling and shaping is 15~22℃. (5) Key points of process operation
① The process temperature control for extruding ABS resin should be as low as possible. Pay attention that the residence time of the molten material in the barrel should not be too long to avoid the decomposition of the molten material. The decomposition temperature of the melt is 250°C. ② When producing ABS pipes, the color of the melt should be observed frequently, and the plasticizing temperature should be reasonably controlled if the melt is pale yellow. When the molten material is light green gray, it means that the temperature of the barrel is too high, and the temperature of the barrel should be lowered immediately.
③The distance between the sizing sleeve and the die should be controlled within the range of 15~35mm.
④If the temperature control of the barrel process is reasonable, but there is still a phenomenon of melt decomposition (the color of the melt is light blue-gray), it should be considered that the length-diameter ratio of the screw should be smaller.
⑤ The working speed of the screw should not be too high, generally not more than 20r/min.
(6) Quality requirements The quality requirements of ABS pipes should comply with HG21561-94 -346-
(2) ABS pipe is out of the molding production process route - use within the temperature range of 2 ~ 20 ℃, but pay attention to this kind of pipe should not be used outside the meal, but it should be determined first, all systems, inspection → inspection → ABS tree The wandering green virgin one anti-exit machine plasticizes the raw material to make it molten one mold agricultural management
(3) Under the conditions, the extrusion molding of ABS pipe mainly adopts the structure of single screw extruder screw. Generally, the same thread pitch should be used, and the thread depth should be gradual; Compression ratio in the range of ~18)1 is (3~4)1-type pipe general structure
(4) Forming process
There are many types of BS resins, and resins suitable for extrusion should be selected, such as E-7 produced by the synthetic rubber factory of Lanzhou Petrochemical Industry Company.
3 or E1 type ABS resin.
②Before the raw materials are put into production, they should be dried and dehumidified in an oven at 70~80℃46
Control the moisture content below 0.1%.
The plasticizing section is 165~180℃, and the homogenizing section is 170~180℃. .③The plasticized raw material is in molten state, and the temperature of the extruder barrel is 150~165℃ in the feeding section
④The temperature of the forming die for forming the tube blank is 175~190℃. ⑤ The draft ratio is 1~1.2.
⑥The temperature of circulating water for cooling and shaping is 15~22℃. (5) Key points of process operation
① The process temperature control for extruding ABS resin should be as low as possible. Pay attention that the residence time of the molten material in the barrel should not be too long to avoid the decomposition of the molten material. The decomposition temperature of the melt is 250°C. ② When producing ABS pipes, the color of the melt should be observed frequently, and the plasticizing temperature should be reasonably controlled if the melt is pale yellow. When the molten material is light green gray, it means that the temperature of the barrel is too high, and the temperature of the barrel should be lowered immediately.
③The distance between the sizing sleeve and the die should be controlled within the range of 15~35mm.
④If the temperature control of the barrel process is reasonable, but there is still a phenomenon of melt decomposition (the color of the melt is light blue-gray), it should be considered that the length-diameter ratio of the screw should be smaller.
⑤ The working speed of the screw should not be too high, generally not more than 20r/min.
(6) Quality requirements The quality requirements of ABS pipes should comply with HG21561-94 -346-
Author：admin